Black Decker Trimmer gl280 User Manual

GL280  
GL301  
GL315  
GL337  
GL350  
 
A
C
E
B
D
F
3
 
G
H
I
J
K
4
L
 
M
N
O
 
5
Intended use  
Residual risks.  
Your Black & Decker trimmer has been designed for trimming  
and finishing lawn edges and to cut grass in confined spaces.  
This appliance is intended for consumer use only.  
Additional residual risks may arise when using the tool which  
may not be included in the enclosed safety warnings. These  
risks can arise from misuse, prolonged use etc.  
Even with the application of the relevant safety regulations  
and the implementation of safety devices, certain residual  
risks can not be avoided. These include:  
u Injuries caused by touching any rotating/moving  
parts.  
u Injuries caused when changing any parts, blades or  
accessories.  
u Injuries caused by prolonged use of a tool. When  
using any tool for prolonged periods ensure you take  
regular breaks.  
Safety instructions  
Warning! When using mains-powered appliances, basic  
safety precautions, including the following, should always be  
followed to reduce the risk of fire, electric shock, personal  
injury and material damage.  
u Read all of this manual carefully before operating the  
appliance.  
u The intended use is described in this manual. The use of  
any accessory or attachment or the performance of any  
operation with this appliance other than those recommended  
in this instruction manual may present a risk of personal  
injury.  
u Impairment of hearing.  
u Health hazards caused by breathing dust developed  
when using your tool (example:- working with wood,  
especially oak, beech and MDF.)  
u Retain this manual for future reference.  
Using your appliance  
After use  
Always take care when using the appliance.  
u Always use safety glasses or goggles.  
u Never allow children or people unfamiliar with the  
instructions to use the appliance.  
u Do not allow children or animals to come near the work  
area or to touch the appliance or power supply cord.  
u Close supervision is necessary when the appliance is  
used near children.  
u When not in use, the appliance should be stored in a dry,  
well ventilated place out of reach of children.  
u Children should not have access to stored appliances.  
u When the appliance is stored or transported in a vehicle it  
should be placed in the boot or restrained to prevent  
movement following sudden changes in speed or direction.  
Inspection and repairs  
u This appliance is not intended for use by young or infirm  
persons without supervision.  
u This appliance is not to be used as a toy.  
u Only use the appliance in daylight or good artificial light.  
u Use in a dry location only. Do not allow the appliance to  
become wet.  
u Before use, check the appliance for damaged or defective  
parts. Check for breakage of parts and any other  
conditions that may affect its operation.  
u Do not use the appliance if any part is damaged or defective.  
u Have any damaged or defective parts repaired or replaced  
by an authorised repair agent.  
u Do not immerse the appliance in water.  
u Do not open the body casing. There are not user-  
serviceable parts inside.  
u Never attempt to remove or replace any parts other than  
those specified in this manual.  
u Do not operate the appliance in explosive atmospheres,  
such as in the presence of flammable liquids, gases or  
dust.  
u To reduce the risk of damage to plugs or cords, never pull  
the cable to remove the plug from a socket.  
Using an extension cable  
Always use an approved extension cable suitable for the  
power input of this appliance (see technical data). The extension  
cable must be suitable for outdoor use and marked accordingly.  
Up to 30 m of 1.5 mm2 HO5VV-F extension cable can be used  
without loss of product performance. Before use, inspect the  
extension cable for signs of damage, wear and ageing.  
Replace the extension cable if damaged or defective.  
When using a cable reel, always unwind the cable completely.  
Safety of others  
u This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge,  
unless they have been given supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety.  
Additional safety instructions for grass trimmers  
Warning! Cutting elements continue to rotate after the motor  
is switched off.  
u Children must be supervised to ensure that they do not  
play with the appliance.  
u Be familiar with the controls and the proper use of the  
appliance.  
6
 
u Before use, check the power supply cord and extension  
cord for signs of damage, ageing and wear. If a cord  
becomes damaged during use, disconnect the cord from  
the mains supply immediately. DO NOT TOUCH THE  
CORD BEFORE DISCONNECTING THE SUPPLY.  
u Do not use the appliance if the cords are damaged or worn.  
u Wear stout shoes or boots to protect your feet.  
u Wear long trousers to protect your legs.  
Keep people and animals at least 6 m away from the  
cutting area.  
8
R
Do not expose the appliance to rain or high humidity.  
Electrical safety  
u Before using the appliance, check that your cutting path is  
free from sticks, stones, wire and any other obstacles.  
u Only use the appliance in the upright position, with the  
cutting line near the ground. Never switch the appliance  
on in any other position.  
u Move slowly when using the appliance. Be aware that  
freshly cut grass is damp and slippery.  
u Do not work on steep slopes. Work across the face of  
slopes, not up and down.  
u Never cross gravel paths or roads while the appliance is  
running.  
u Never touch the cutting line while the appliance is running.  
u Do not put the appliance down until the cutting line has  
come to a complete standstill.  
This appliance is double insulated; therefore no earth  
wire is required. Always check that the power supply  
corresponds to the voltage on the rating plate.  
#
u If the supply cord is damaged, it must be replaced by the  
manufacturer or an authorised Black & Decker Service  
Centre in order to avoid a hazard.  
Features  
This appliance includes some or all of the following features.  
1. On/off switch  
2. Handle  
3. Cable restraint  
4. Power inlet  
5. Secondary handle  
6. Tube  
u Use only the appropriate type of cutting line.  
Never use metal cutting line or fishing line.  
u Be careful not to touch the line trimming blade.  
u Take care to keep the mains cable away from the cutting  
line. Always be aware of the position of the cable.  
u Keep hands and feet away from the cutting line at all  
times, especially when switching on the motor.  
u Before using the appliance and after any impact, check for  
signs of wear or damage and repair as necessary.  
u Never operate the appliance with damaged guards or  
without guards in place.  
7. Storage hooks  
8. Adjustment button  
9. Guard  
10. Line trimming blade  
11. Cutting line  
12. Spool housing  
13. Edge guide  
14. Head  
u Take care against injury from any device fitted for trimming  
the filament line length. After extending new cutter line  
always return the machine to its normal operating position  
before switching on.  
Assembly  
Warning! Before assembly, make sure that the tool is  
switched off and unplugged.  
u Always ensure that the ventilation slots are kept clear of  
debris.  
u Do not use the lawn trimmer (edge trimmer), if the cords  
are damaged or worn.  
Attaching the tube to the head (fig. A)  
u Align the rectangular tab of the tube (6) with the location in  
the head (14).  
u Insert the tube into the head and push until it clicks into place.  
u Keep extension cords away from cutting elements.  
Attaching the handle to the tube (fig. B)  
u Align the square tab of the tube (6) with the location in the  
handle (2).  
Labels on appliance  
The following warning symbols are found on the appliance:  
u Insert the tube into the handle and push until it clicks into  
place.  
+
Read the manual prior to operation.  
Fitting the guard (fig. C)  
Wear safety glasses or goggles when operating this  
appliance.  
u Remove the screw (15) from the head.  
u Place the guard onto the tool as shown.  
u Firmly press the guard (9) until it snaps into place.  
F
 
7
u Secure the guard with the screw.  
Hints for optimum use  
Warning! Never use the tool unless the guard is properly fitted.  
General  
Releasing the cutting line  
u In order to achieve optimum cutting results, only cut dry  
In transit, the cutting line is taped to the spool housing.  
u Remove the tape holding the cutting line (11) to the spool  
housing (12).  
grass.  
Trimming  
u Hold the tool as shown in fig. F.  
Connecting the tool to the mains (fig. D)  
u Connect the female plug of a suitable extension cable to  
the power inlet (4).  
u Gently swing the trimmer from side to side.  
u When cutting long grass, work in stages from the top.  
Take small cuts.  
u Loop the cable through the cable restraint (3).  
u Insert the mains plug into a mains outlet.  
For wired in cable units: Make sure the cable is looped through  
the cable restraint prior to connecting the plug to the mains  
outlet.  
u Keep the tool away from hard objects and delicate plants.  
u If the tool starts running slowly, reduce the load.  
Edging  
Optimum cutting results are achieved on edges deeper than  
50 mm.  
Warning! The extension cable must be suitable for outdoor  
use.  
u Do not use the tool to create edges. To create edges,  
use an edging spade.  
u Guide the tool as shown in fig. G.  
u To make a closer cut, slightly tilt the tool.  
Use  
Warning! Let the tool work at its own pace. Do not overload.  
Fitting a new spool of cutting line (fig. H - J)  
Setting the tool to trimming or edging mode  
(fig. E - G)  
Spool with single cutting line (fig. H)  
The tool can be used in trimming mode as shown in fig. F or in  
edging mode to trim overhanging grass along lawn edges and  
flower beds as shown in fig. G.  
Replacement spools of cutting line are available from your  
Black & Decker dealer (cat. no. A6481).  
u Keep the tabs (16) depressed and remove the spool cover  
(17) from the housing (12).  
Trimming mode (fig. E & F)  
For trimming, the trimmer head should be in the position  
shown in fig. F. If it is not:  
u Remove the empty spool (18) from the spool housing.  
u Remove any dirt and grass from the spool cover and housing.  
u Take the new spool and unwind approximately 9 cm of  
cutting line.  
u Depress the adjustment button (8).  
u Rotate the head (14), while releasing the button.  
u When the head is in position, the button will lock into place.  
Note: The tube will only rotate in one direction.  
u Feed the cutting line through the eyelet (19).  
u Push the spool onto the drive shaft (20) and rotate it  
slightly until it is seated. Make sure that the cutting line is  
not trapped under the spool and that 9 cm of cutting line  
protrudes from the housing.  
Edging mode (fig. E & G)  
For edging, the trimmer head should be in the position shown  
in fig. G. If it is not:  
u Align the tabs on the spool cover with the holes in the  
housing.  
u Depress the adjustment button (8).  
u Push the cover onto the housing until it snaps securely  
into place.  
Warning! If the cutting line protrudes beyond the trimming  
blade (10), cut it off so that they just reach the blade.  
u Rotate the head (14), while releasing the button.  
u When the head is in position, the button will lock into place.  
Note: The tube will only rotate in one direction.  
Switching on and off  
Spool with twin cutting line (fig. I & J)  
u To switch the tool on, squeeze the trigger lever (1).  
u To switch the tool off, release the trigger lever.  
Warning! Never attempt to lock the trigger lever in the on  
position.  
Replacement spools of cutting line are available from your  
Black & Decker dealer (cat. no. A6441). Complete cassettes  
containing a spool of cutting line are also available  
(cat. no. A6488).  
u Keep the tabs (21) depressed and remove the spool cover  
(22) from the housing (12).  
8
 
-
Temporarily park the line in the slots (33) on one side of  
the spool as shown.  
u Remove the empty spool (23) from the spool cover.  
u Remove any dirt and grass from the spool cover and  
housing.  
u Take the new spool and push it onto the boss in the spool  
cover. Rotate the spool slightly until it is seated.  
u Unclip the end of one of the cutting lines and feed the line  
into one of the eyelets (24). The line should protrude  
approximately 9 cm from the spool cover.  
u Repeat the above procedure for the second cutting line on  
the lower section of the spool. Park the line in the unused  
slots (33).  
u Proceed as described above to fit the spool on the tool.  
Do not forget to release the cutting line from the parking  
slots (33).  
Warning! Only use the appropriate type of Black & Decker  
cutting line. Ensure that cutting line is present in both sections  
of the spool.  
u Unclip the end of the other cutting line and feed the line  
into the other eyelet. The line should protrude  
approximately 9 cm from the spool cover.  
u Align the tabs (21) on the spool cover with the cut-outs (25)  
in the housing.  
u Push the cover onto the housing until it snaps securely  
into place.  
Mains plug replacement (U.K. & Ireland only)  
If a new mains plug needs to be fitted:  
u Safely dispose of the old plug.  
Warning! If the cutting lines protrude beyond the trimming  
blade (10), cut them off so that they just reach the blade.  
u Connect the brown lead to the live terminal in the new plug.  
u Connect the blue lead to the neutral terminal.  
Warning! No connection is to be made to the earth terminal.  
Follow the fitting instructions supplied with good quality plugs.  
Recommended fuse: 5 A.  
Winding a new cutting line onto an empty spool  
(fig. K - O)  
You may wind new cutting line onto an empty spool.  
Troubleshooting  
If your tool seems not to operate properly, follow the  
instructions below. If this does not solve the problem, please  
contact your local Black & Decker repair agent.  
Spool with single cutting line (fig. K & L)  
Replacement packs of cutting line are available from your  
Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).  
u Remove the empty spool from the tool as described above.  
u Remove any remaining cutting line from the spool.  
u Feed 2 cm of cutting line into one of the holes (26) in the  
spool as shown.  
Warning! Before proceeding, unplug the tool.  
Appliance runs slowly  
u Bend the cutting line and anchor it in the L-shaped slot (27).  
u Wind the cutting line onto the spool in the direction of the  
arrow (28). Make sure to wind the line on neatly and in  
layers. Do not criss-cross.  
u When the wound cutting line reaches the recesses (29),  
cut the line. Let the line protrude approximately 9 cm from  
the spool and hold a finger on the line to keep it in place.  
u Proceed as described above to fit the spool on the tool.  
Warning! Only use the appropriate type of Black & Decker  
cutting line.  
u Check that the spool housing can rotate freely. Carefully  
clean it if necessary.  
u Check that the cutting line does not protrude more than  
11 cm from the spool housing. If it does, cut it off so that it  
just reaches the line trimming blade.  
Automatic line feed does not work  
u Keep the tabs depressed and remove the spool cover  
from the housing.  
u Pull the cutting line until it protrudes 11 cm from the  
housing. If insufficient cutting line is left on the spool,  
install a new spool of cutting line as instructed above.  
u Align the tabs on the spool cover with the cut outs in the  
housing.  
Spool with twin cutting line (fig. M - O)  
Replacement packs of cutting line are available from your  
Black & Decker dealer (cat. no. A6440).  
u Remove the empty spool from the tool as described above.  
u Remove any remaining cutting line from the spool.  
u First wind new line onto the uppermost part of the spool:  
u Push the cover onto the housing until it snaps securely  
into place.  
u If the cutting line protrudes beyond the trimming blade,  
cut it off so that it just reaches the blade.  
If the automatic line feed still does not work or the spool is  
jammed, try the following suggestions:  
u Carefully clean the spool cover and housing.  
u Remove the spool and check if the lever can move freely.  
-
Feed 2 cm of cutting line into one of the slots (30) in the  
upper section of the spool as shown.  
-
Wind the cutting line onto the spool in the direction of  
the arrow (31). Make sure to wind the line on neatly  
and in layers. Do not criss-cross.  
-
When the wound cutting line reaches the recesses (32),  
cut the line.  
 
9
You can check the location of your nearest authorised repair  
agent by contacting your local Black & Decker office at the  
address indicated in this manual. Alternatively, a list of  
authorised Black & Decker repair agents and full details of our  
after-sales service and contacts are available on the Internet  
u Remove the spool and unwind the cutting line, then wind it  
on neatly again as described above. Replace the spool as  
instructed.  
Maintenance  
Your Black & Decker corded/cordless appliance/tool has been  
designed to operate over a long period of time with a minimum  
of maintenance. Continuous satisfactory operation depends  
upon proper tool/appliance care and regular cleaning.  
Technical data  
GL280 GL301 GL315  
TYPE 2 TYPE 2 TYPE 3  
Input voltage  
Power input  
No-load speed  
Weight  
VAC 230  
300  
230  
300  
230  
320  
Warning! Before performing any maintenance on corded/  
cordless power tools:  
u Switch off and unplug the appliance/tool.  
u Or switch off and remove the battery from the appliance/  
tool if the appliance/tool has a separate battery pack.  
u Or run the battery down completely if it is integral and then  
switch off.  
W
min-1 10,000 10,000 10,000  
kg 2.2  
2.2  
2.2  
GL337 GL350  
TYPE 2 TYPE 3  
Input voltage  
Power input  
No-load speed  
Weight  
VAC 230  
320  
230  
350  
u Unplug the charger before cleaning it. Your charger does  
not require any maintenance apart from regular cleaning.  
u Regularly clean the ventilation slots in your tool/appliance  
and charger using a soft brush or dry cloth.  
W
min-1 10,000 10,000  
kg 2.2  
2.2  
u Regularly clean the motor housing using a damp cloth.  
Do not use any abrasive or solvent-based cleaner.  
Hand/arm weighted vibration value according to EN 786:  
= 4 m/s2 , uncertainty (K) = 1.5 m/s2 ,  
Protecting the environment  
Separate collection. This product must not be  
Z
disposed of with normal household waste.  
Should you find one day that your Black & Decker product  
needs replacement, or if it is of no further use to you, do not  
dispose of it with household waste. Make this product  
available for separate collection.  
Separate collection of used products and packaging  
z
allows materials to be recycled and used again.  
Re-use of recycled materials helps prevent  
environmental pollution and reduces the demand for  
raw materials.  
Local regulations may provide for separate collection of  
electrical products from the household, at municipal waste  
sites or by the retailer when you purchase a new product.  
Black & Decker provides a facility for the collection and  
recycling of Black & Decker products once they have reached  
the end of their working life. To take advantage of this service  
please return your product to any authorised repair agent who  
will collect them on our behalf.  
10  
 
EC declaration of conformity  
MACHINERY DIRECTIVE  
OUTDOOR NOISE DIRECTIVE  
Guarantee  
Black & Decker is confident of the quality of its products and  
offers an outstanding guarantee. This guarantee statement is  
in addition to and in no way prejudices your statutory rights.  
The guarantee is valid within the territories of the Member  
States of the European Union and the European Free Trade  
Area.  
%
GL280/GL301/GL315/GL337/GL350  
If a Black & Decker product becomes defective due to faulty  
materials, workmanship or lack of conformity, within  
24 months from the date of purchase, Black & Decker  
guarantees to replace defective parts, repair products  
subjected to fair wear and tear or replace such products to  
ensure minimum inconvenience to the customer unless:  
u The product has been used for trade, professional or hire  
purposes;  
Black & Decker declares that these products described under  
"technical data" are in compliance with:  
2006/42/EC, EN 60335-1, EN 60335-2-91  
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII  
KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem,  
The Netherlands  
Notified Body ID No.: 0344  
u The product has been subjected to misuse or neglect;  
u The product has sustained damage through foreign  
objects, substances or accidents;  
u Repairs have been attempted by persons other than  
authorised repair agents or Black & Decker service staff.  
Level of accoustic power according to 2000/14/EC  
(Article 12, Annex III, L ≤ 50 cm):  
LWA (measure sound power) 95 dB(A)  
uncertainty (K) = 3 dB(A)  
LWA (guaranteed sound power) 96 dB(A)  
uncertainty (K) = 3 dB(A)  
To claim on the guarantee, you will need to submit proof of  
purchase to the seller or an authorised repair agent. You can  
check the location of your nearest authorised repair agent by  
contacting your local Black & Decker office at the address  
indicated in this manual. Alternatively, a list of authorised  
Black & Decker repair agents and full details of our after-sales  
service and contacts are available on the Internet at:  
These products also comply with directive 2004/108/EC.  
For more information, please contact Black & Decker at the  
following address or refer to the back of the manual.  
The undersigned is responsible for compilation of the technical  
file and makes this declaration on behalf of Black & Decker.  
Please visit our website www.blackanddecker.co.uk to  
register your new Black & Decker product and to be kept up to  
date on new products and special offers. Further information  
on the Black & Decker brand and our range of products is  
Kevin Hewitt  
Vice-President Global Engineering  
Black & Decker Europe, 210 Bath Road, Slough,  
Berkshire, SL1 3YD  
_
United Kingdom  
01-10-2009  
UK patent application no.: 059745.6  
European Community design application nos. 340385-0001 &  
339544-0001  
 
11  
12  
 
 
13  
14  
 
ENGLISH  
Do not forget to register your product!  
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product  
code to Black & Decker in your country.  
 
Australia  
Black & Decker (Australia) Pty. Ltd.  
20 Fletcher Road, Mooroolbark,  
Victoria, 3138  
Tel. 03-8720 5100  
Fax 03-9727 5940  
New Zealand  
Black & Decker  
5 Te Apunga Place  
Mt Wellington  
Tel. +64 9 259 1133  
Fax +64 9 259 1122  
Auckland 1060  
United Kingdom  
Black & Decker  
210 Bath Road  
Tel. 01753 511234  
Fax 01753 551155  
Helpline 01753 574277  
Slough, Berkshire SL1 3YD  
90553705 REV-0  
03/2010  
 

Belkin Laptop F5U302 User Manual
Black Decker Lawn Mower Accessory 688153 01 User Manual
Black Decker Vacuum Cleaner 598033 02 User Manual
Bosch Appliances Cooktop PCK755UC User Manual
Breville Blender BBL910XL User Manual
Brother Fax Machine FAX 400 User Manual
Campbell Hausfeld Automobile AL2130 User Manual
Carrier Furnace 58MTB User Manual
Casio Watch 2213 User Manual
Chief Manufacturing TV Mount nag1bw User Manual